3D Printable Car Parts · New Zealand

Gauge pods built for the Subaru Legacy.

Hand-modelled for the actual dash geometry. No generic templates, no guesswork. Gen2, Gen3 and Gen4 Legacy covered. RHD and LHD. Buy the STL files or order printed and shipped to NZ or AUS.

Jump to section
Gen4 BL/BP Gen3 BH/BE Gen2 BD/BG/BK RHD & LHD No Permanent Mods Not AI Generated
View Products Request a Design
Gen2 + Gen3 + Gen4
Legacy generations covered
52mm
Standard gauge sizing
RHD & LHD
Both drives, every product
NZ$0 mods
Press-fit, zero permanent mods
Products
Generation 4 Legacy (2003–2009) — BL / BP Gen 4
◈
Website Exclusive

2-Piece Design — Included with Every Gen4 Purchase

Every Gen4 gauge pod sold here ships with the 2-piece design: a dedicated vent clip and a separate pod body. The clip installs once into the factory defrost vent and stays put. The pod body then locks into the clip, giving a precise fit and a clean removal when you need it. Better retention, easier cable routing, and no rattling. This design is exclusive to direct website purchases.

Gen4 Triple Offset Gauge Pod 52mm Gen4 Triple Offset Gauge Pod 52mm Gen4 Triple Offset Gauge Pod 52mm
Gen4 BL/BP Triple Gauge Offset Layout
Triple Offset Vent Gauge Pod — 52mm
  • Three gauges in an offset layout for maximum dash clearance
  • Fully adjustable angle — set it exactly where you need it
  • Clean cable routing through the factory vent
  • RHD & LHD files included
  • 2-piece vent clip design included
  • Recommended material: ASA — UV and heat resistant
NZ$17 STL files
Gen4 Triple Vent Gauge Pod 52mm Gen4 Triple Vent Gauge Pod 52mm
Gen4 BL/BP Triple Gauge
Triple Vent Gauge Pod — 52mm
  • Three gauges in a straight layout, sits flush in the defrost vent
  • Three pod lengths included: standard, mid (25mm shorter), low profile (35mm shorter)
  • Secure press-fit, no permanent modifications
  • Clean cable routing — nothing on show
  • RHD & LHD files for all three lengths
  • 2-piece vent clip design included
  • Recommended material: ASA — UV and heat resistant
NZ$22 STL files — 7 files included
Gen4 Double Gauge Pod 52mm Gen4 Double Gauge Pod 52mm
Gen4 BL/BP Double Gauge
Double Vent Gauge Pod — 52mm
  • Two-gauge pod designed for the BL/BP dash geometry
  • Internal press-fit ring — clean removal, no damage to interior
  • Cable routing through the vent keeps the install tidy
  • RHD & LHD files included
  • 2-piece vent clip design included
  • Recommended material: ASA — UV and heat resistant
NZ$15 STL files
Gen4 Single Gauge Pod 52mm Gen4 Single Gauge Pod 52mm
Gen4 BL/BP Single Gauge
Single Vent Gauge Pod — 52mm
  • One gauge, designed for the BL/BP defrost vent slot
  • The clean starting point — boost, oil temp or AFR
  • Press-fit into the factory vent — no permanent modifications
  • RHD & LHD files included
  • 2-piece vent clip design included
  • Recommended material: ASA — UV and heat resistant
NZ$12.50 STL files
Gen4 Single Gauge Pod 60mm
Gen4 BL/BP Single Gauge 60mm
Single Vent Gauge Pod — 60mm
  • Same BL/BP defrost vent fitment, sized for 60mm aftermarket gauges
  • Designed for the larger-diameter gauges common in JDM builds
  • Press-fit into the factory vent — no permanent modifications
  • RHD & LHD files included
  • 2-piece vent clip design included
  • Recommended material: ASA — UV and heat resistant
NZ$12.50 STL files
Generation 3 Legacy (1998–2003) — BH / BE Gen 3
⚙️
2-Piece Design

Pod + Vent Clip — both files included

Every Gen3 purchase includes the gauge pod body and the custom vent retention clip. Press-fit installation — no permanent modifications, no cutting.

Gen3 Subaru Legacy Single Gauge Pod — CAD render
Gen3 BH/BE Single Gauge RHD
Vent Gauge Pod — 52mm
  • Single 52mm gauge mount — fits BH Wagon and BE Sedan (1998–2003)
  • 2-piece design — pod + vent clip, both STLs included
  • Press-fits into factory defrost vent — no permanent mods
  • Recommended material: ASA — UV and heat resistant
NZ$12.50 STL files — instant download
Gen3 Subaru Legacy Double Gauge Pod Gen3 Subaru Legacy Double Gauge Pod installed Gen3 Subaru Legacy Double Gauge Pod Gen3 Legacy Double Gauge Pod — CAD render
Gen3 BH/BE Double Gauge RHD
Double Vent Gauge Pod — 52mm
  • Two 52mm gauge mounts side-by-side — fits BH Wagon and BE Sedan (1998–2003)
  • 2-piece design — pod + vent clip, both STLs included
  • Press-fits into factory defrost vent — no permanent mods
  • Recommended material: ASA — UV and heat resistant
NZ$15.00 STL files — instant download

More Gen3 variants in development.
Triple pod coming once fit-testing is complete.

Get notified →
Generation 2 Legacy — BD / BG / BK Gen 2
Gen2 Subaru Legacy Gauge Pod 52mm Gen2 Subaru Legacy Gauge Pod 52mm
Gen2 BG/BD/BK Single Gauge
Vent Gauge Pod — 52mm
★ 5.0
  • Gauge holder for the defrost vent on Gen2 Legacy (BG/BD/BK)
  • Internal press-fit ring — secure hold, clean removal
  • Verified by buyers — top-rated in the range
  • Recommended material: ASA — UV and heat resistant
NZ$12.50 STL files
Gen2 Subaru Legacy Double Gauge Pod 52mm — In Development
In Development
Gen2 BG/BD/BK Double Gauge
Double Vent Gauge Pod — 52mm
  • Two 52mm gauges in the Gen2 defrost vent
  • Design complete — fit testing in progress
  • RHD variant first, LHD to follow
  • Notify me when available
Coming Soon
Notify Me →
Gen2 Subaru Legacy Triple Gauge Pod 52mm — In Development
In Development
Gen2 BG/BD/BK Triple Gauge
Triple Vent Gauge Pod — 52mm
  • Three 52mm gauges in the Gen2 defrost vent
  • Design complete — fit testing in progress
  • RHD variant first, LHD to follow
  • Notify me when available
Coming Soon
Notify Me →
Gen4 Legacy Suspension Parts — BL/BP 2003–2009 Gen4 BL/BP
⚠️
Safety Notice — Read Before Purchasing

Suspension components — use at your own risk

These are functional 3D printed parts, not certified automotive components. TPU filament only — rigid materials (PLA, PETG, ASA) are unsafe for this application. Professional inspection and installation is strongly recommended before driving. By purchasing you accept full responsibility for fitment, use, and any outcome. Full disclaimer →

Gen4 Subaru Legacy Sway Bar Bushing 19mm
Gen4 BL/BP 19mm Suspension
Sway Bar Bushing — 19mm
  • Direct replacement for Gen4 Legacy front or rear sway bar
  • Split two-piece design — installs without dropping the bar
  • Print in TPU for flex or PETG for a firmer feel
  • 19mm internal bore — verify your bar diameter before printing
NZ$8 STL file
Gen4 Subaru Legacy Sway Bar Bushing 20mm
Gen4 BL/BP 20mm Suspension
Sway Bar Bushing — 20mm
  • Direct replacement for Gen4 Legacy front or rear sway bar
  • Split two-piece design — installs without dropping the bar
  • Print in TPU for flex or PETG for a firmer feel
  • 20mm internal bore — verify your bar diameter before printing
NZ$8 STL file
Gen4 Subaru Legacy Sway Bar Bushing 21mm
Gen4 BL/BP 21mm Suspension
Sway Bar Bushing — 21mm
  • Direct replacement for Gen4 Legacy front or rear sway bar
  • Split two-piece design — installs without dropping the bar
  • Print in TPU for flex or PETG for a firmer feel
  • 21mm internal bore — verify your bar diameter before printing
NZ$8 STL file
Universal Gauge Accessories — Fits Any 52mm Gauge Universal
52mm Universal Gauge Visor Anti-Glare Hood
Universal 52mm Anti-Glare
52mm Gauge Visor — Universal Anti-Glare Hood
  • Slides over any standard 52mm gauge — no vehicle-specific fitment
  • Cuts windscreen glare and direct sun off the gauge face
  • Low-profile cylindrical design — looks factory
  • No adhesive — friction fit onto the gauge bezel
NZ$5 STL file

More universal gauge accessories coming soon.
Got a request? Get in touch.

Request a design →
Customer Reviews
Loading reviews…
Why Our Parts
01

Hand-modelled, not AI

Every pod is designed to the specific dash geometry of that Legacy generation. If it does not fit perfectly, it does not ship.

02

Both drives covered

Every product includes RHD and LHD variants. Legacy owners are worldwide — we design for all of them.

03

Heat and UV resistant

Designed for ASA filament. Your dash gets hot enough to warp PLA — we recommend the material that actually survives a NZ summer.

04

No permanent mods

Press-fit into the factory defrost vent. No glue, no damage. Comes out clean if you change your mind.

About

One person. One workshop. Zero shortcuts.

NZSDesigns started because nobody was making proper gauge pods for the Subaru Legacy. The kind that fit cleanly, look like they belong there, and leave your interior exactly as it was. So I designed my own.

Every design is hand-modelled from measurements taken on real cars. Gen2, Gen3 and Gen4 Legacy models, 52mm and 60mm sizing, available in both RHD and LHD. Not copied, not AI-generated. If I would not run it in my own car, it does not ship.

The press-fit system keeps things reversible. The pod locks into the factory defrost vent and comes out clean. No glue, no cutting. Website purchases for Gen4 include the 2-piece design — a vent clip that stays installed permanently, with the pod body clicking in and out for cable management and future changes.

This is a one-person operation. You are dealing directly with the person who designed the part and will actually reply to your message. No support queue, no form submissions into a void.

After a Legacy variant that is not listed, or need something custom? Get in touch.

Ready to run gauges properly?

Printed to order and shipped to NZ and AUS, or download the STL files and print yourself. Questions about fitment, materials or a custom design? Just ask.

Browse all products View Gen4, Gen3 & Gen2
→
Custom or custom design hello@nzsdesigns.com
→